[ REQ 5333]: I cannot run Geomview on my Alpha

[jrs at BACCHUS.NECTAR.CS.CMU.EDU]

Hello,

I just downloaded the binary distribution of Geomview for DEC Alpha
workstations.  The downloading, uncompressing, untaring, and installation
all seemed to proceed well.  However, when I try to run geomview, the
result is:

bacchus] geomview &
[1] 16390
bacchus] X Toolkit Warning: Representation size 4 must match superclass's to override baseWidth
X Toolkit Warning: Representation size 8 must match superclass's to override iconPixmap
X Toolkit Warning: Representation size 4 must match superclass's to override iconX
Unaligned access pid=16390 <gvx> va=2d393538386f7cf9 pc=3ff802e026c ra=300001806cc type=ldq

[1]    Segmentation fault   geomview


My DEC 3000 is running OSF/1 v. 2.0.  I don't imagine this information is
enough to diagnose the problem, but if you have any suggestions, I'd love
to hear them.

Thanks,
Jonathan Shewchuk
jrs at cs.cmu.edu

P.S.  Here's my "install.log":

GEOMROOT=/afs/cs.cmu.edu/project/quake/code/Geomview
BINDIR=/afs/cs.cmu.edu/project/quake/code/Geomview/bin
MANDIR=/afs/cs.cmu.edu/project/quake/code/Geomview/man
MACHTYPE=x11
MMAPACKAGEDIR=/afs/cs.cmu.edu/project/quake/code/Geomview/mathematica
Installed bin/x11/bdy in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/clip in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/math2oogl in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/oogl2rib in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/anytooff in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/offconsol in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/polymerge in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/anytoucd in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/ucdtooff in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/geomview in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/togeomview in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/geomstuff in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
Installed bin/x11/medit2gv in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
(null command)
Edited "geomview" to set GEOMROOT=/afs/cs.cmu.edu/project/quake/code/Geomview.
Removed previously existing /afs/cs.cmu.edu/project/quake/code/Geomview/bin/geom
view
Installed geomview in /afs/cs.cmu.edu/project/quake/code/Geomview/bin
The manual page files are in /afs/cs.cmu.edu/project/quake/code/Geomview/man (no
t
  installed outside the Geomview distribution directory).
The Mathematica packages are in /afs/cs.cmu.edu/project/quake/code/Geomview/math
ematica (not
  installed outside the Geomview distribution directory).
*** Can't run 'maple' to install Maple-to-Geomview script
*** /afs/cs.cmu.edu/project/quake/code/Geomview/maple/gvplot.m.  To install it m
anually,
*** see the instructions in /afs/cs.cmu.edu/project/quake/code/Geomview/doc/gvpl
ot.doc.


Geomview installation complete.